Revo Voron E3D

RAPIDCHANGE

We’ve developed this Revo-compatible cold side in collaboration with Team Voron. It’s intended for use with the Voron StealthBurner, which includes an integrated cold side fan. It’s compatible with our Revo ecosystem, so you can change nozzle size without tools or hot tightening using just your fingers.

• Uses Revo Nozzles – change nozzles cold, no tools, no hot tightening
• Works with a Revo HeaterCore for faster heat-ups
• Rigid mounting using 4 x M3 x 0.5 bolts
• Ultra-lightweight construction for improved speed performance
• Ideal HotEnd for Voron StealthBurner

Ready for Revo. A groove at the bottom of the sink accepts a Revo HeaterCore spring. It’s compatible with our Revo ecosystem, so you can change nozzles without tools or hot tightening using just your fingers.

Complements your Voron. Includes an anodised red aluminium heatsink to complement your Voron accented parts.

Rigid mounting. This is a rigid mounted design that uses four M3 x 0.5 bolts to secure to your Voron 3D printer.

Compatible with:

Please note:

– For full mounting instructions and STL files for Voron printed parts visit: https://docs.vorondesign.com/

– You may need to adjust your Z offset when changing nozzles.

Key Features:

– Max temp: 300°C

– Voltage: 24V

– Wattage: 40W

– Mounting System: 4 x M3 x 0.5

– Filament diameter: 1.75

– Nozzle type: RapidChange Revo

Revo Voron E3D Kit Includes:

– 1 x Revo Voron Sink

– 1 x Revo HeaterCore 24V

– 1 x Revo spring

– 1 x 100mm 1.75mm PTFE

– 1 x Heater extension cable

– 1 x Temperature sensor extension cable

Single nozzle kit:

– 1 x 0.40mm brass Revo Nozzle

Fully loaded nozzle kit:

– 1 x 0.25, 0.40, 0.60, and 0.80mm brass Revo Nozzles

E3D Revo Hemera Upgrade Single Nozzle Kit

This kit includes a Hemera heatsink with a revised design that’s compatible with a Revo HeaterCore and Revo Nozzles.

– Updated Hemera heatsink adds compatibility for Revo Nozzles and Revo HeaterCore

– Easy upgrade! Just swap over your old Hemera heatsink and attach the Revo HeaterCore

– Comes in your choice of a single Revo Nozzle or a Fully Loaded Nozzle Kit

– Compatible with 1.75mm filaments

Please note: this kit comes in 12V or 24V options.

E3D Revo Hemera Upgrade Single Nozzle Kit  includes:

– 1 x Revo Hemera sink

– 1 x Revo HeaterCore

– 1 x Revo HeaterCore spring

– 1 x Extension cable kit

– 1x  0.40

E3D Revo Hemera Upgrade Fully Loaded Kit

This kit includes a Hemera heatsink with a revised design that’s compatible with a Revo HeaterCore and Revo Nozzles.

– Updated Hemera heatsink adds compatibility for Revo Nozzles and Revo HeaterCore

– Easy upgrade! Just swap over your old Hemera heatsink and attach the Revo HeaterCore

– Comes in your choice of a single Revo Nozzle or a Fully Loaded Nozzle Kit

– Compatible with 1.75mm filaments

Please note: this kit comes in 12V or 24V options.

E3D Revo Hemera Upgrade Fully Loaded Kit Kit includes:

– 1 x Revo Hemera sink

– 1 x Revo HeaterCore

– 1 x Revo HeaterCore spring

– 1 x Extension cable kit

– 1x 0.25, 0.40, 0.60, 0.80

E3D Revo Micro Fully Loaded Kit

Ready for Revo. Change nozzles at room temperature using just your fingers. No complex tools, no hot tightening. Revo Nozzles are a factory sealed nozzle and heatbreak in one, so they’re easy to fit and can’t leak material when in use. 

New hotness. A Revo HeaterCore heats up in seconds. It’s much safer too – unlike other solutions on the market, a positive temperature coefficient (PTC) means the Revo HeaterCore can not melt at extreme temperatures: power reduces as it gets hotter, so hazards are reduced in the event of a thermal runaway. 

Runs cool, looks cool. With an anodised black heatsink, not only does Revo Micro run cool – it looks cool, too. 

Flexible to any setup. Revo Micro plays nice with Bowden and direct drive setups, but its lightweight construction makes it an ideal choice for Bowden setups.

Please note: 

– This kit does not include any 3D printed mounts

– The Revo Micro fan must be connected using the 5V regulator unless connecting directly to a 5V pin

– This kit comes with 100mm of PTFE tube

E3D Revo Micro Fully Loaded Kit Key features: 

– Max temp: 300C

– Weight: 30g

– Nozzle type: RapidChange Revo

– Maximum temp: 300°C

– M12 x 1.5 thread mounting

– Compatible with Bowden and direct drive systems

E3D Revo Micro Fully Loaded Kit includes:

– 1 x Revo Micro heatsink

– 1 x M12 x 1.5 nut

– 1 x 20 x 20 x 10 5V fan

– 1 x 12V or 24V to 5V regulator board

– 1 x Revo Micro fan duct

– 1 x Collet

– 1 x Collet clip

– 1 x Revo HeaterCore 12V or 24V

– 1 x Revo HeaterCore spring

– 1 x Extension cable kit

– 1 x 100mm PTFE

E3D Revo Micro Fully loaded nozzle kit:

– 1 x 0.25, 0.40, 0.60, and 0.80mm brass Revo Nozzles