E3D Revo Six Single Nozzle Kit

No machine redesign. Revo Six is a top choice if you want to update your old E3D V6 setup to the latest generation of E3D HotEnd technology. It has the same height, the same diameter, and the same groove mount as the E3D V6, so it drops straight into V6-fitted machines without the hassle of redesigning print head mounts and accessories. Just fit it, connect the Revo HeaterCore, and you’re ready to 3D print. 

Ready for Revo. Revo Six is designed to work with Revo Nozzles, so you can perform nozzle swaps with your fingers at room temperature without complex tools or hot tightening. Each Revo Nozzle is factory sealed, making it much simpler to use and more reliable than most HotEnd technology available today. 

Enhanced performance. Revo Six uses a Revo HeaterCore, our latest HotEnd heating and sensing architecture. It reaches temperature much faster than a traditional aluminium HeaterBlock, and it’s much safer: a positive temperature coefficient (PTC) means the HeaterCore can’t melt at extreme temperatures, reducing hazards in the event of a thermal runaway. 

A new look. An anodised black heat sink distinguishes Revo Six from its predecessor, and every unit ships with a premium crystal-clear fan duct so your machine will stand out from the crowd.

Compatible with:

Prusa i3 MK2/ MK3 variants (make sure you select the correct voltage for your setup)

E3D Revo CR

E3D Revo CR is a drop-in upgrade for some of the most popular Creality 3D printers available, including the Creality CR-10 and Ender 3 series.

• Upgrade your Creality 3D printer to Revo so you can change nozzles cold without special tools and hot tightening hassles
• No extra mounts or adapters needed: Pre-drilled M3 clearance holes match Creality’s X carriage mounting pattern for easy installation
• No firmware tweaks: This kit includes a special Revo HeaterCore with a 100K NTC thermistor, which has the same response as the stock Creality thermistor
• Includes solderless, crimpless, butt splice connectors for easy connection. Wire the HeaterCore into your Creality 3D printer without undoing your entire cable bundle
• Detailed [upgrade guides] created by us help you get 3D printing quickly

Creality mounting holes. Convenient M3 clearance holes correspond to Creality’s X carriage mounting pattern, so you can get up and running quickly without extra mounts or adaptors. Just reuse the existing M3 bolts!

Easy nozzle swaps. A variety of Revo Nozzles enhance the capabilities of your 3D printer without a difficult nozzle changing processes. Every Revo Nozzle can be changed by hand. No tools, no hot tightening.

Simple, hassle-free connection. We’ve included some solderless, crimpless, butt splice connectors for easy connection to help you get up and running quickly without having to undo your entire wiring bundle.

Better reliability. Revo Nozzles are factory sealed, so there’s much less chance of nozzle leaks, and no hot tightening needed.

Better efficiency. The included Revo HeaterCore makes your 3D printer heat up faster and more efficiently than the stock HotEnd. Start 3D printing right away without annoying firmware adjustments: we’ve integrated a 100K NTC thermistor into this special HeaterCore. This thermistor has the same response as the stock HotEnd, so no firmware tweaks are needed.

Better safety. Thanks to built-in PTC behaviour of the heater, Revo CR will add an extra failsafe against thermal runaways to your Creality 3D printer – providing an extra layer of protection if thermal runaway protection is disabled in firmware.

E3D Revo CR is directly compatible with the following Creality 3D printers:

• Ender 3
• Ender 3 Pro
• Ender 3 V2
• Ender 5
• Ender 5 Pro
• Ender 5 Plus
• Ender 6
• CR10
• CR10S
• CR10S4
• CR10S5

Please note:

• Revo CR can be used with other Creality printers using the NTC thermistor, however you may need to make modifications to the mount and or Z sensor.
• You may need to adjust the Z height when changing nozzles.
• Please check whether your specific printer runs 12V or 24V before purchasing and assembling.

Variants

Revo CR + Revo Nozzle

Revo CR Fully Loaded

Key features

– Max temp: 300°C

– Works with Revo HeaterCore and Revo Nozzles

– Includes solderless, crimpless, butt splice connectors for easy connection

– 100K NTC thermistor embedded in this Revo HeaterCore

 Kit contains

– 1 x  Revo CR heatsink

– 1 x Collet

– 1 x Collet clip

– 1 x Revo HeaterCore 12V or 24V

– 1 x Revo HeaterCore spring

– 1 x Extension cable kit

– 4 x butt splice connector

E3D Revo CR Single nozzle kit:

– 1 x 0.40mm brass Revo Nozzle

E3D Revo CR Fully loaded nozzle kit:

– 1 x 0.25, 0.40, 0.60, and 0.80mm brass Revo Nozzles

Note: M3 bolts not provided

Material compatibility

1.75mm

Mount system

Flat mounting, pre-drilled M3 clearance holes that match Creality mounting pattern

E3D Revo CR Voltage

12V or 24V

Dimensions

Height: 59.10mm

Diameter: 22mm

Revo Voron E3D

RAPIDCHANGE

We’ve developed this Revo-compatible cold side in collaboration with Team Voron. It’s intended for use with the Voron StealthBurner, which includes an integrated cold side fan. It’s compatible with our Revo ecosystem, so you can change nozzle size without tools or hot tightening using just your fingers.

• Uses Revo Nozzles – change nozzles cold, no tools, no hot tightening
• Works with a Revo HeaterCore for faster heat-ups
• Rigid mounting using 4 x M3 x 0.5 bolts
• Ultra-lightweight construction for improved speed performance
• Ideal HotEnd for Voron StealthBurner

Ready for Revo. A groove at the bottom of the sink accepts a Revo HeaterCore spring. It’s compatible with our Revo ecosystem, so you can change nozzles without tools or hot tightening using just your fingers.

Complements your Voron. Includes an anodised red aluminium heatsink to complement your Voron accented parts.

Rigid mounting. This is a rigid mounted design that uses four M3 x 0.5 bolts to secure to your Voron 3D printer.

Compatible with:

Please note:

– For full mounting instructions and STL files for Voron printed parts visit: https://docs.vorondesign.com/

– You may need to adjust your Z offset when changing nozzles.

Key Features:

– Max temp: 300°C

– Voltage: 24V

– Wattage: 40W

– Mounting System: 4 x M3 x 0.5

– Filament diameter: 1.75

– Nozzle type: RapidChange Revo

Revo Voron E3D Kit Includes:

– 1 x Revo Voron Sink

– 1 x Revo HeaterCore 24V

– 1 x Revo spring

– 1 x 100mm 1.75mm PTFE

– 1 x Heater extension cable

– 1 x Temperature sensor extension cable

Single nozzle kit:

– 1 x 0.40mm brass Revo Nozzle

Fully loaded nozzle kit:

– 1 x 0.25, 0.40, 0.60, and 0.80mm brass Revo Nozzles

E3D Revo Hemera Upgrade Single Nozzle Kit

This kit includes a Hemera heatsink with a revised design that’s compatible with a Revo HeaterCore and Revo Nozzles.

– Updated Hemera heatsink adds compatibility for Revo Nozzles and Revo HeaterCore

– Easy upgrade! Just swap over your old Hemera heatsink and attach the Revo HeaterCore

– Comes in your choice of a single Revo Nozzle or a Fully Loaded Nozzle Kit

– Compatible with 1.75mm filaments

Please note: this kit comes in 12V or 24V options.

E3D Revo Hemera Upgrade Single Nozzle Kit  includes:

– 1 x Revo Hemera sink

– 1 x Revo HeaterCore

– 1 x Revo HeaterCore spring

– 1 x Extension cable kit

– 1x  0.40

E3D Revo Hemera Upgrade Fully Loaded Kit

This kit includes a Hemera heatsink with a revised design that’s compatible with a Revo HeaterCore and Revo Nozzles.

– Updated Hemera heatsink adds compatibility for Revo Nozzles and Revo HeaterCore

– Easy upgrade! Just swap over your old Hemera heatsink and attach the Revo HeaterCore

– Comes in your choice of a single Revo Nozzle or a Fully Loaded Nozzle Kit

– Compatible with 1.75mm filaments

Please note: this kit comes in 12V or 24V options.

E3D Revo Hemera Upgrade Fully Loaded Kit Kit includes:

– 1 x Revo Hemera sink

– 1 x Revo HeaterCore

– 1 x Revo HeaterCore spring

– 1 x Extension cable kit

– 1x 0.25, 0.40, 0.60, 0.80

E3D Revo Micro Fully Loaded Kit

Ready for Revo. Change nozzles at room temperature using just your fingers. No complex tools, no hot tightening. Revo Nozzles are a factory sealed nozzle and heatbreak in one, so they’re easy to fit and can’t leak material when in use. 

New hotness. A Revo HeaterCore heats up in seconds. It’s much safer too – unlike other solutions on the market, a positive temperature coefficient (PTC) means the Revo HeaterCore can not melt at extreme temperatures: power reduces as it gets hotter, so hazards are reduced in the event of a thermal runaway. 

Runs cool, looks cool. With an anodised black heatsink, not only does Revo Micro run cool – it looks cool, too. 

Flexible to any setup. Revo Micro plays nice with Bowden and direct drive setups, but its lightweight construction makes it an ideal choice for Bowden setups.

Please note: 

– This kit does not include any 3D printed mounts

– The Revo Micro fan must be connected using the 5V regulator unless connecting directly to a 5V pin

– This kit comes with 100mm of PTFE tube

E3D Revo Micro Fully Loaded Kit Key features: 

– Max temp: 300C

– Weight: 30g

– Nozzle type: RapidChange Revo

– Maximum temp: 300°C

– M12 x 1.5 thread mounting

– Compatible with Bowden and direct drive systems

E3D Revo Micro Fully Loaded Kit includes:

– 1 x Revo Micro heatsink

– 1 x M12 x 1.5 nut

– 1 x 20 x 20 x 10 5V fan

– 1 x 12V or 24V to 5V regulator board

– 1 x Revo Micro fan duct

– 1 x Collet

– 1 x Collet clip

– 1 x Revo HeaterCore 12V or 24V

– 1 x Revo HeaterCore spring

– 1 x Extension cable kit

– 1 x 100mm PTFE

E3D Revo Micro Fully loaded nozzle kit:

– 1 x 0.25, 0.40, 0.60, and 0.80mm brass Revo Nozzles

E3D Revo Six Fully Loaded Kit

No machine redesign. Revo Six is a top choice if you want to update your old E3D V6 setup to the latest generation of E3D HotEnd technology. It has the same height, the same diameter, and the same groove mount as the E3D V6, so it drops straight into V6-fitted machines without the hassle of redesigning print head mounts and accessories. Just fit it, connect the Revo HeaterCore, and you’re ready to 3D print. 

Ready for Revo. Revo Six is designed to work with Revo Nozzles, so you can perform nozzle swaps with your fingers at room temperature without complex tools or hot tightening. Each Revo Nozzle is factory sealed, making it much simpler to use and more reliable than most HotEnd technology available today. 

Enhanced performance. Revo Six uses a Revo HeaterCore, our latest HotEnd heating and sensing architecture. It reaches temperature much faster than a traditional aluminium HeaterBlock, and it’s much safer: a positive temperature coefficient (PTC) means the HeaterCore can’t melt at extreme temperatures, reducing hazards in the event of a thermal runaway. 

A new look. An anodised black heat sink distinguishes Revo Six from its predecessor, and every unit ships with a premium crystal-clear fan duct so your machine will stand out from the crowd.

Compatible with:

Prusa i3 MK2/ MK3 variants (make sure you select the correct voltage for your setup)